Nortel Passport 8600 Series Installation Manual Download Page 70

Page: 70 / 164

Ethernet Routing Switch 8600 module fundamentals

Table 26
8691 SF/CPU module LEDs (cont’d.)

Label

Color, State

Meaning

Green, Steady

The management port is operating at 100 Mbps.

100

Off

The management port is operating at 10 Mbps.

The number of lit LEDs indicates the utilization
level (full-duplex operation) of the switch fabric
as follows:

1 LED = 10 Mbps

5 LEDs = 10 Gbps

2 LEDs =100 Mbps

6 LEDs = 20 Gbps

3 LEDs = 1 Gbps

7 LEDs = 40 Gbps

Switch Utilization (8 LEDs)

Green

4 LEDs = 5 Gbps

8 LEDs = 64 Gbps

The number of lit LEDs indicates the level
(full-duplex operation) of CPU activity as follows:

1 LED = 12%

5 LEDs = 60%

2 LEDs = 24%

6 LEDs = 72%

3 LEDs = 36%

7 LEDs = 84%

CPU Utilization
(8 LEDs)

Green

4 LEDs = 48%

8 LEDs = 100%

Green, Steady

The specified power supply is operating
normally.

Amber, Steady

The specified power supply failed.

Power Supply 1, 2, 3

Off

A power supply is not present in the specified
bay, or the power supply in the specified bay is
not turned on.

Green, Steady

The specified fan is operating normally.

Amber, Steady

The specified fan is present in the chassis and
failed, or no fan is present in the chassis and
should be present.

Fan 1, 2

Off

The specified fan is not present in the chassis
(and should not be present).

Green, Steady

The temperature is normal for switch operation.

Temp

Amber, Steady

The maximum operating temperature is
exceeded.

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Summary of Contents for Passport 8600 Series































































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Nortel Passport 8600 Series, Installation Manual, Page: 70 / 164

Search results

Summary of Contents for Passport 8600 Series

Reviews: