Nortel Passport 8600 Series Installation Manual Download Page 128

Page: 128 / 164

128

Technical specifications

Table 57
8672ATME and 8672ATMM power specifications

Specification

Value

3.3 V power (W)

64.4

12 V power (W)

30.0

Total power (W)

94.4

8683POSM module

The following table describes the 8683POSM module specifications.

Table 58
8683POSM module specifications

Physical specifications

Height:

1.5 in. (3.8 cm)

Width:

15.4 in. (39.1 cm)

Depth:

18.5 in. (47.0 cm)

Weight:

Electrical specifications

Input power:

OC-3c MDA: 70 W maximum

OC-12c MDA: 90 W maximum

Thermal rating:

OC-3c MDA: 241 Btu/hr maximum

OC-12c MDA: 310 Btu/hr maximum

MTBF rating

255 693 hr

Connector types

OC-3c MDA: MT-RJ

OC-12c MDA: Duplex SC

Cable specifications

Type:

Multimode or single mode fiber optic
cable

Maximum distance:

Multimode fiber optic cable:

1.24 mi (2 km) for OC-3c
connection

1640 ft (500 m) for OC-12c
connection

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Summary of Contents for Passport 8600 Series































































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Nortel Passport 8600 Series, Installation Manual, Page: 128 / 164

Search results

Summary of Contents for Passport 8600 Series

Reviews: