manualshive.com logo in svg

Nortel Passport 8600 Series, Installation Manual, Page: 151 / 164

Share
Download
Nortel Passport 8600 Series Installation Manual Download Page 151

151

.

Appendix
Translations of Safety Messages

This section contains translations of precautionary notices that you must
read and follow for safe operation of the Nortel Ethernet Routing Switch
8600.

Navigation

•

“Class A electromagnetic interference caution statement” (page 151)

•

“Electromagnetic interference caution statement” (page 152)

•

“Electrostatic discharge caution statement” (page 154)

•

“Laser eye safety warning statement” (page 155)

Class A electromagnetic interference caution statement

CAUTION

Risk of electromagnetic interference

This device is a Class A product. Operation of this equipment
in a residential area is likely to cause harmful interference, in
which case users are required to take appropriate measures
necessary to correct the interference at their own expense.

CAUTION

ATTENTION

Le périphérique est un produit de Classe A. Le fonctionnement
de cet équipement dans une zone résidentielle risque de causer
des interférences nuisibles, auquel cas l’utilisateur devra y
remédier à ses propres frais.

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Copyright © 2008 Nortel Networks

.

Summary of Contents for Passport 8600 Series





































































































































































Reviews:

No comments