manualshive.com logo in svg

Nortel Passport 8600 Series, Installation Manual, Page: 100 / 164

Share
Download
Nortel Passport 8600 Series Installation Manual Download Page 100

100

Module installation and connection

CAUTION

Risk of data loss

You must remove the card from the SF/CPU module
before changing the read-write protection. Failure
to remove the card can result in improper write
protection.

2

Adjust the read-write protect switch.

3

Reinsert the memory card.

--End--

Installing the Enterprise enhanced CPU daughter card

Install the Enterprise enhanced CPU daughter card (SuperMezz) to offload
processing from the CPU to the daughter card, and to enable use of all
Ethernet Routing Switch 8600 features.

Installing a SuperMezz takes appriximately 10 minutes.

ATTENTION

If you have a system with two Ethernet Routing Switch 8692SF/CPU modules,
you must install the daughter card on each of the modules.

Prerequisites

•

The 8692 SF/CPU is removed from the Ethernet Routing Switch 8600
using proper removal procedures.

CAUTION

Electrostatic discharge can damage hardware. See

“Job aid:

avoiding ESD” (page 87)

.

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Copyright © 2008 Nortel Networks

.

Summary of Contents for Passport 8600 Series





































































































































































Reviews:

No comments