Nortel Passport 8600 Series Installation Manual Download Page 63

Page: 63 / 164

Interface module descriptions

The 8648GTRS forwarding engine has 2 lanes. Each lane supports
10Gbps and operates in full-duplex mode.

RS modules are not compatible with the 8001AC and 8002DC power
supplies or the 8691 SF/CPU modules. You must use the 8692 SF/CPU
in chassis that contain RS modules. RS modules interoperate with
R modules.

The following figure shows the location of the 8648GTRS module LEDs.

Figure 35
8648GTRS module LEDs

The following table describes the 8648GTRS module LEDs.

Table 21
8648GTRS module LEDs

Type

Label

Color, State

Meaning

Green, Steady

The port is operating at 1000 Mbps.

Amber, Steady

The port is operating at 100 Mbps.

10/100/1000
(no label)

Off

The port is operating at 10 Mbps

Green, blinking 1:1
flash (1/2 on, 1/2 off)

The port is transmitting or receiving
data.

Amber, Steady

The port is administratively disabled.

Port

Activity/Link
(no label)

Off

The port has no link.

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Summary of Contents for Passport 8600 Series































































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Nortel Passport 8600 Series, Installation Manual, Page: 63 / 164

Search results

Summary of Contents for Passport 8600 Series

Reviews: