Nortel Passport 8600 Series Installation Manual Download Page 131

Page: 131 / 164

8634XGRS module

131

Table 61
8630GBR module specifications (cont’d.)

Electrical specifications

Thermal rating:

614.1 Btu/hr maximum

MTBF rating

177 525 hr

Connector type

SFP—LC (fiber)

The following table provides power data for an 8630GBR module filled with
short-range SFPs. For power additions for middle and long-range SFPs,
see

“SFPs, XFPs, R and RS modules, and power consumption” (page 66)

Table 62
8630GBR power specifications-including short range SFP power

Specification

Value

3.3 V power (W)

60.1

12 V power (W)

120.0

Total power (W)

180.1

8634XGRS module

The following table describes the 8634XGRS module specifications.

Table 63
8634XGRS module specifications

Physical specifications

Height:

1.5 in. (3.8 cm)

Width:

15.4 in. (39.1 cm)

Depth:

18.5 in. (47.0 cm)

Weight:

10 lb (4.54 kg)

Electrical specifications

Input power:

259.1 W maximum (includes XFPs
and SFPs). See the following table.

Thermal rating:

883.5 Btu/hr maximum

MTBF rating

369 190 hr

Connector type

Performance specifications

Aggregate throughput

8.5 Gbps

The following table provides power data for an 8634XGRS module
filled with short-range SFP/XFPs. For power additions for middle and
long-range SFP/XFPs, see

“SFPs, XFPs, R and RS modules, and power

consumption” (page 66)

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Summary of Contents for Passport 8600 Series































































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Nortel Passport 8600 Series, Installation Manual, Page: 131 / 164

Search results

Summary of Contents for Passport 8600 Series

Reviews: