Nortel Passport 8600 Series Installation Manual Download Page 51

Page: 51 / 164

Interface module descriptions

Advertisements (CANA). For more information about CANA, see Nortel
Ethernet Routing Switch 8600 Configuration — Ethernet Modules,
NN46205-503.

The following figure shows the location of the 8648GTR module LEDs.

Figure 23
8648GTR module LEDs

The following table describes the 8648GTR module LEDs.

Table 12
8648GTR module LEDs

Type

Label

Color, State

Meaning

Green, Steady

The port is operating at 1000 Mbps.

Amber, Steady

The port is operating at 100 Mbps.

10/100/1000
(no label)

Off

The port is operating at 10 Mbps

Amber, Blinking

An error is detected.

Green, Steady

The port is connected and the link is
operational.

Green, Blinking

Data is passing through the port. The
blink rate indicates the level of link
activity.

Amber, Steady

The port is administratively disabled.

Port

Link/Activity
(no label)

Off

The port has no link.

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Summary of Contents for Passport 8600 Series































































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Nortel Passport 8600 Series, Installation Manual, Page: 51 / 164

Search results

Summary of Contents for Passport 8600 Series

Reviews: