manualshive.com logo in svg

Nortel Passport 8600 Series, Installation Manual, Page: 53 / 164

Share
Download
Nortel Passport 8600 Series Installation Manual Download Page 53

Interface module descriptions

53

Figure 24
8683XLR module

The 8683XLR module supports up to three 10 Gigabit Ethernet small form
factor-pluggable (XFP) transceivers. Although some of the XFPs are
LAN/WAN (that is, LR/LW, ER/EW, ZR/ZW) this module only uses the LAN
functionality.

For a list of Nortel-qualified XFPs, see

“Nortel-qualified SFPs, XFPs, and

GBICs” (page 64)

.

Nortel recommends that you install only one 10GBASE-ZR/ZW XFP in
one 8683XLR module due to cooling limitations on the 8683XLR and
XZR modules when using standard fan trays. Nortel further recommends
that you install the XFP only in Port 1. You can install a 10GBASE-SR,
-LR/LW, or ER/EW in one or both of the remaining ports.

There are no XFP limitations for this module in any slot when using the
new cooling modules for the 8010 and 8006 chassis.

The following figure shows the location of the 8683XLR module LEDs.

Figure 25
8683XLR module LEDs

The following table describes the 8683XLR module LEDs.

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Copyright © 2008 Nortel Networks

.

Summary of Contents for Passport 8600 Series





































































































































































Reviews:

No comments