manualshive.com logo in svg

Nortel Passport 8600 Series, Installation Manual, Page: 64 / 164

Share
Download
Nortel Passport 8600 Series Installation Manual Download Page 64

64

Ethernet Routing Switch 8600 module fundamentals

Table 21
8648GTRS module LEDs (cont’d.)

Type

Label

Color, State

Meaning

Green, Steady

The module has completed the
power-on self-test and software
initialization and is operating normally.

Amber, Steady

The module is in an interim boot state
(nonoperational).

Amber, Blinking

The module failed to boot.

Module

Online

Off

The module power is off.

The Ethernet Routing Switch 8600 8648GTRS is an R series module and
supports:

•

256 000 IP routes

•

64 000 MAC records

•

Release 4.1 and earlier: 16 000 in R mode
Release 5.0 and later: 32 000 in R mode

Nortel-qualified SFPs, XFPs, and GBICs

Nortel qualified the GBICs listed in the following table for use in Ethernet
Routing Switch 8600 interface modules. Only GBICs qualified by Nortel
are supported for use in Ethernet Routing Switch 8600 modules. GBICs
not qualified by Nortel can operate within the module, but are not tested for
power draw, electromagnetic interference, or interoperability.

Table 22
Nortel-qualified GBICs

GBIC order number

Description

AA1419041-E5

1000BASE-T, RJ-45, up to 100 m

AA1419001-E5

1000BASE-SX, SC connectors, 850 nm, up to 275
or 550 m

AA1419002-E5

1000BASE-LX, SC connectors, 1310 nm, up to
10 km

AA1419003-E5

1000BASE-XD, SC connectors, 1550 nm, up to
50 km

AA1419004-E5

1000BASE-ZX, SC connectors, 1550 nm, up to
70 km

AA1419017-E5 to
AA1419024-E5

1000BASE-EX, CWDM 1470 nm to 1610 nm, SC
connectors, up to 120 km

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Copyright © 2008 Nortel Networks

.

Summary of Contents for Passport 8600 Series





































































































































































Reviews:

No comments