manualshive.com logo in svg

Nortel Passport 8600 Series, Installation Manual, Page: 79 / 164

Share
Download
Nortel Passport 8600 Series Installation Manual Download Page 79

8661 SSL Acceleration Module

79

Figure 41
SAM faceplate

The following table describes the faceplate items.

Table 28
Item description for 8661 SAM faceplate

Item

Description

1

Maintenance port (DIN-8 connector)

2

LEDs

You can install one or two 8661 SAMs in the 8006 chassis. You can
install a maximum of four 8661 SAMs in the 8010 or 8010co chassis. The
chassis into which you install the SAM must contain at least one Web
Switching Module.

You cannot install the 8661 SAM in an 8003 chassis.

For information about how to perform 8661 SAM system configuration and
maintenance, see Nortel Ethernet Routing Switch 8600 Configuration —
8661 SSL Accelerator with the Web Switching Module, NN46205-514.

SAM LEDs

The 8661 SAM includes an Online LED that indicates overall status for the
module and an Active LED to indicate traffic status. The following figure
shows the location of the LEDs on the 8661 SAM.

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Copyright © 2008 Nortel Networks

.

Summary of Contents for Passport 8600 Series





































































































































































Reviews:

No comments