manualshive.com logo in svg

Nortel Passport 8600 Series, Installation Manual, Page: 13 / 164

Share
Download
Nortel Passport 8600 Series Installation Manual Download Page 13

Safety Messages

13

Safety Messages

This section describes the different precautionary notices used in this
document. This section also contains precautionary notices that you must
read for safe operation of the Nortel Ethernet Routing Switch 8600.

Notices

Notice paragraphs alert you about issues that require your attention.
The following sections describe the types of notices. For a list of safety
messages used in this guide and their translations, see "Translations of
safety messages".

Attention Notice

ATTENTION

An attention notice provides important information regarding the installation and
operation of Nortel products.

Caution ESD Notice

CAUTION

ESD

ESD notices provide information about how to avoid discharge
of static electricity and subsequent damage to Nortel products.

CAUTION

ESD (décharge électrostatique)

La mention ESD fournit des informations sur les moyens de
prévenir une décharge électrostatique et d’éviter d’endommager
les produits Nortel.

CAUTION

ACHTUNG ESD

ESD-Hinweise bieten Information dazu, wie man die
Entladung von statischer Elektrizität und Folgeschäden an
Nortel-Produkten verhindert.

CAUTION

PRECAUCIÓN ESD (Descarga electrostática)

El aviso de ESD brinda información acerca de cómo evitar
una descarga de electricidad estática y el daño posterior a los
productos Nortel.

CAUTION

CUIDADO ESD

Os avisos do ESD oferecem informações sobre como evitar
descarga de eletricidade estática e os conseqüentes danos aos
produtos da Nortel.

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Copyright © 2008 Nortel Networks

.

Summary of Contents for Passport 8600 Series





































































































































































Reviews:

No comments