Nortel Passport 8600 Series Installation Manual Download Page 117

Page: 117 / 164

8608GTE and 8608GTM modules

117

8608GBE and 8608GBM modules

The following table provides specifications for the 8608GBE and -M
modules.

Table 36
8608GBX module specifications

Physical specifications

Height:

1.5 in. (3.8 cm)

Width:

15.4 in. (39.1 cm)

Depth:

18.5 in. (47.0 cm)

Weight:

8.0 lb (3.6 kg)

Input power

65 W maximum

Thermal rating

224 Btu/hr maximum

Mean time between failure (MTBF)

197 096 hours (hr)

Connector type

GBIC—SC (fiber) or RJ-45 (copper)

8608GTE and 8608GTM modules

The following table provides specifications for the 8608GTE and -M
modules.

Table 37
8608GTX module specifications

Physical specifications

Height:

1.5 inches (in.); 3.8 centimeters (cm)

Width:

15.4 in. (39.1 cm)

Depth:

18.5 in. (47.0 cm)

Weight:

8.0 pounds (lb); 3.6 kilograms (kg)

Electrical specifications

Input power:

138.1 Watts (W) maximum. See the
following table.

Thermal rating:

470.9 Btu/hr maximum

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Summary of Contents for Passport 8600 Series































































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Nortel Passport 8600 Series, Installation Manual, Page: 117 / 164

Search results

Summary of Contents for Passport 8600 Series

Reviews: