manualshive.com logo in svg

Nortel Passport 8600 Series, Installation Manual, Page: 139 / 164

Share
Download
Nortel Passport 8600 Series Installation Manual Download Page 139

WSM

139

WSM

The following table lists the electrical, cable, and optical specifications of
the WSM. The WSM uses SC connectors, and RJ-45 connectors wired
as MDI.

Table 80
WSM specifications

Physical specifications

Height:

1.5 in. (3.8 cm)

Width:

15.4 in. (39.1 cm)

Depth:

18.5 in. (47.0 cm)

Weight:

14.0 lb (6.4 kg)

Electrical specifications

Input power:

120 W maximum

Thermal rating:

340 BTU/hr maximum

MTBF rating:

79 273 hours (calculated)

Cable specifications

Category 3, 4, or 5 UTP cable (10 Mbps
operation)

Category 5 UTP cable (100 Mbps
operation

10/100BASE-T

Maximum distance: 328 ft (100 m)

1000BASE-SX

62.5

µ

m multimode fiber optic cable:

•

722 ft (220 m) @ 160 MHz/km
bandwidth

•

902 ft (275 m) @ 200 MHz/km
bandwidth

50

µ

m multimode fiber optic cable:

•

1604 ft (500 m) @ 400 MHz/km
bandwidth

•

1804 ft (550 m) @ 400 MHz/km
bandwidth

Optical specifications

Wavelength:

850 nm

Optical Budget:

7 dB

Minimum Launch Power:

-10 dBm

Maximum Launch Power:

-4 dBm

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Copyright © 2008 Nortel Networks

.

Summary of Contents for Passport 8600 Series





































































































































































Reviews:

No comments