Nortel Passport 8600 Series Installation Manual Download Page 120

Page: 120 / 164

120

Technical specifications

Cable specifications

•

1640 ft (500 m) @ 400
MHz-km bandwidth

•

1804 ft (550 m) @ 400
MHz-km bandwidth

Table 43
8608SXE optical specifications

Optical specifications

Wavelength:

850 nm

Optical budget:

7 dB

Laser transmitter characteristics:

Minimum launch power: -10 dBm

Maximum launch power: -4 dBm

Receiver characteristics:

Minimum receiver sensitivity: -17
dBm

Maximum input power: 0 dBm

8616GTE module

The following table provides specifications for the 8616GTE modules.

Table 44
8616GTE specifications

Physical specifications

Height:

1.5 in. (3.8 cm)

Width:

15.4 in. (39.1 cm)

Depth:

18.5 in. (47.0 cm)

Weight:

8.0 lb (3.6 kg)

Electrical specifications

Input power:

129.2 W maximum

Thermal rating:

440.6 Btu/hr maximum

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Summary of Contents for Passport 8600 Series































































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Nortel Passport 8600 Series, Installation Manual, Page: 120 / 164

Search results

Summary of Contents for Passport 8600 Series

Reviews: