Nortel Passport 8600 Series Installation Manual Download Page 104

Page: 104 / 164

104

Module installation and connection

Procedure steps

Step

Action

Turn on and configure the terminal or a communications port on
the PC using the parameters in the following table.

See the PC or terminal user manual for instructions.

Parameter

Value

Baud rate

9600

Data bits

Stop bits

Parity

None

Insert the 9-pin receptacle end of the console cable into the
console connector on the 8691 SF/CPU or 8692 SF/CPU
module, or to the maintenance port of the WSM.

Attach the 9-pin plug end of the cable to the serial
communications port on the back of the PC or terminal.

--End--

Connecting a modem to the SF/CPU

Use an AT or Hayes-compatible modem and serial cable to provide remote
dial-in access to the CLI.

Procedure steps

Step

Action

Turn on and configure the modem, using the parameters in the
following table.

See the modem documentation for instructions.

Setting

Value

Clear to send (CTS) signal

Data terminal ready (DTR)
signal

Modem can only connect if the DTR
signal is present. If the DTR signal is
not present, the modem disconnects.

Data carrier detect (DCD) or
received line signal detection
(RLSD)

On while the carrier is present. The
switch uses DCD to detect modem
connect and disconnect.

Data set ready (DSR) signal

Ready to send (RTS) signal

Ignored

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Summary of Contents for Passport 8600 Series































































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Nortel Passport 8600 Series, Installation Manual, Page: 104 / 164

Search results

Summary of Contents for Passport 8600 Series

Reviews: