manualshive.com logo in svg

Nortel Passport 8600 Series, Installation Manual, Page: 40 / 164

Share
Download
Nortel Passport 8600 Series Installation Manual Download Page 40

40

Ethernet Routing Switch 8600 module fundamentals

Figure 12
8624FXE module

The 24 100BASE-FX ports on the 8624FXE module can operate in 100
Mbps Fast Ethernet full-duplex mode. The optical transceivers provide
transmission ranges of up to 6562 ft (2 km) using 62.5 µm multimode fiber
cable or 4264 ft (1.3 km) using 50 µm multimode fiber cable.

The following figure shows the location of the LEDs.

Figure 13
8624FXE module LEDs

The following table describes the 8624FXE module LEDs.

Table 6
8624FXE module LEDs

Type

Label

Color, State

Meaning

Green, Steady

The port is connected and the link is
operational.

Green, Blinking

Data is passing through the port.

Amber, Steady

A fault condition exists at the far end of the
connection.

Port

Link/Act

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Copyright © 2008 Nortel Networks

.

Summary of Contents for Passport 8600 Series





































































































































































Reviews:

No comments