Nortel Passport 8600 Series Installation Manual Download Page 126

Page: 126 / 164

126

Technical specifications

The ports on both the 8648TXE and 8648TXM modules are RJ-45 ports
wired as MDI-X connectors (see the following table).

Table 55
Pin assignments: 8648TXE/8648TXM module port

Connector

Pin number

Signal

Input receive data + (RX+)

Input receive data - (RX-)

Output transmit data + (TX+)

Output transmit data - (TX-)

4, 5, 7, 8

Not used

8672ATME and 8672ATMM modules

The following table provides specifications for the ATM modules.

Table 56
ATM module specifications

Physical specifications

Height

1.5 in. (3.8 cm)

Width

15.4 in. (39.1 cm)

Depth

18.5 in. (47.0 cm)

Weight

8.0 lb (3.6 kg)

Electrical specifications

Input power:

OC-3c MDA: 40 W maximum

OC-12c MDA: 40 W maximum

DS-3 MDA: 40 W maximum

Thermal rating:

OC-3c MDA: 138 Btu/hr maximum

OC-12c MDA: 138 Btu/hr maximum

DS-3 MDA: 138 Btu/hr maximum

MTBF rating

222 103 hr

Connector type

OC-3c MDA: MT-RJ

OC-12c MDA: Duplex SC

DS-3 MDA: BNC

Cable specifications

Type

Multimode or single mode fiber optic
cable, coaxial cable

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Summary of Contents for Passport 8600 Series































































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Nortel Passport 8600 Series, Installation Manual, Page: 126 / 164

Search results

Summary of Contents for Passport 8600 Series

Reviews: