Nortel Passport 8600 Series Installation Manual Download Page 105

Page: 105 / 164

Connecting a network management station to the SF/CPU

105

Setting

Value

Synchronous/asynchronous
mode

Asynchronous

Auto answer

Answer on two rings when DTR is
active.

Local character echo

Off

Supervisory functions

Off

Baud rate

9600

Data bits

Stop bits

Parity

None

Insert the 9-pin receptacle end of the serial cable into the modem
connector on the 8691 SF/CPU or 8692 SF/CPU module.

Insert the 25-pin plug connector into the modem RS-232 data
communications port.

--End--

Connecting a network management station to the SF/CPU

Use the management port to connect the switch to a network management
station for out-of-band management using a Web browser or Device
Manager.

Procedure steps

Step

Action

Connect an Ethernet cable to the network management station.

For 10 Mbps connections, you can use Category 3, 4, or 5
copper unshielded twisted pair (Ethernet) cable. Use only
Category 5 UTP cable to connect ports that operate at 100
Mbps.

Connect the other end of the cable to the RJ-45 jack on the 8691
SF/CPU or 8692 SF/CPU module.

--End--

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Summary of Contents for Passport 8600 Series































































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Nortel Passport 8600 Series, Installation Manual, Page: 105 / 164

Search results

Summary of Contents for Passport 8600 Series

Reviews: