Nortel Passport 8600 Series Installation Manual Download Page 102

Page: 102 / 164

102

Module installation and connection

Press the daughter card assembly into the connectors on the
8692 SF/CPU.

Make sure that the CPU daughter card is properly seated in the
connectors.

Use the hex key to secure the Mezzanine card to the 8692
SF/CPU module with the four socket head screws.

Install the #2-56 x .625 screws first. See the following figure for
correct screw placement. After you place the screw in the hole,
insert the hex key through the mezzanine card hole to secure
the screw.

Do not overtighten the screws. It is normal for a slight space
to be visible between the CPU daughter card and the CPU
standoffs.

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Summary of Contents for Passport 8600 Series































































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Nortel Passport 8600 Series, Installation Manual, Page: 102 / 164

Search results

Summary of Contents for Passport 8600 Series

Reviews: