manualshive.com logo in svg

Nortel Passport 8600 Series, Installation Manual, Page: 61 / 164

Share
Download
Nortel Passport 8600 Series Installation Manual Download Page 61

Interface module descriptions

61

•

256 000 IP routes

•

64 000 MAC records

•

Release 4.1 and earlier: 16 000 in R mode
Release 5.0 and later: 32 000 in R mode

8648GBRS module

The 8648GBRS modules support up to 48 SFPs, 16 ports for each lane.
All RS modules require the high-speed cooling module. The following
figure shows the 8648GBRS.

Figure 32
8648GBRS module

All RS modules support jumbo frames.

RS modules are not compatible with the 8001AC and 8002DC power
supplies or the 8691 SF/CPU modules. You must use the 8692 SF/CPU
in chassis that contain RS modules. RS modules interoperate with
R modules.

For a list of Nortel-qualified SFPs, see

“Nortel-qualified SFPs, XFPs, and

GBICs” (page 64)

.

The following figure shows the LED locations.

Figure 33
8648GBRS module LED locations

The following table describes the 8648GBRS module LEDs.

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Copyright © 2008 Nortel Networks

.

Summary of Contents for Passport 8600 Series





































































































































































Reviews:

No comments