Nortel Passport 8600 Series Installation Manual Download Page 39

Page: 39 / 164

Interface module descriptions

Table 5
8616SXE module LEDs

Type

Label

Color, State

Meaning

Green, Blinking

The port is transferring data.

Off

There is no port activity.

Green, Steady

The port is linked and enabled.

Green, Blinking

The port is receiving data.

Amber, Steady

The port either has no optical signal or no
link synchronization.

Port

Off

The port has a signal, but no link.

Green, Steady

The module completed the power-on self-test
and software initialization and is operating
normally.

Amber, Steady

The module failed the power-on self-test.

Module

Online

Off

The module power is off. If the switch power
is on, the module is performing the power-on
self-test and software initialization. A module
in this state is not yet functional.

The 8616SXE module supports up to 32 000 table entries in its forwarding
engine.

The 8616SXE module does not support R or M mode.

When you use an 8616 module with Auto-Negotiation enabled, set the
re-autoneg flag for proper interoperability. Set the flag using the CLI
command

config bootconfig flags 8616-reautoneg true

or the

NNCLI command

boot config flags 8616-reautoneg

8624FXE module

The 8624FXE module provides 24 100BASE-FX ports using MT-RJ type
connectors (see the following figure).

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Summary of Contents for Passport 8600 Series































































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Nortel Passport 8600 Series, Installation Manual, Page: 39 / 164

Search results

Summary of Contents for Passport 8600 Series

Reviews: