Nortel Passport 8600 Series Installation Manual Download Page 144

Page: 144 / 164

144

Technical specifications

Table 88
8692 SF/CPU specifications (cont’d.)

Connector types

Console port:

DB-9 connector (see

“8692 SF/CPU

Console port” (page 145)

)

Modem port:

DB-9 connector (see

“8692 SF/CPU

modem port” (page 145)

)

Cable specifications

Ethernet Management port:

Category 3, 4, or 5 UTP cable (10
Mbps operation)

Category 5 UTP cable (100 Mbps
operation)

Console port:

RS-232 cable

Modem port:

DTE-to-DCE cable (straight or
transmit cable)

The following table provides power specifications for the 8692 SF/CPU
module.

Table 89
8692 SF/CPU power specifications

Specification

Without SuperMezz

With SuperMezz

3.3 V power (W)

50.2

82.5

12 V power (W)

50.4

60.0

Total power (W)

100.6

142.5

8692 SF/CPU Management port

The Management port is a 10/100 Mbps Ethernet port implemented on an
RJ-45 connector wired as an MDI connection.

The following table shows the pin assignments for this connector.

Table 90
Pin assignments: 8692 SF/CPU module Management port

Connector

Pin number

Signal

Output transmit data + (TX+)

Output transmit data - (TX-)

Input receive data + (RX+)

Input receive data - (RX-)

4, 5, 7, 8

Not used

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Summary of Contents for Passport 8600 Series































































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Nortel Passport 8600 Series, Installation Manual, Page: 144 / 164

Search results

Summary of Contents for Passport 8600 Series

Reviews: