Nortel Passport 8600 Series Installation Manual Download Page 132

Page: 132 / 164

132

Technical specifications

Table 64
8634XGRS power specifications-including short range SFP/XFP power

Specification

Value

3.3 V power (W)

91.7

12 V power (W)

167.4

Total power (W)

259.1

8648GBRS module

The following table describes the 8648GBRS module specifications.

Table 65
8648GBRS module specifications

Physical specifications

Height:

1.5 in. (3.8 cm)

Width:

15.4 in. (39.1 cm)

Depth:

18.5 in. (47.0 cm)

Weight:

10 lb (4.54 kg)

Electrical specifications

Input power:

271.6 maximum (includes SFPs).
See the following table.

Thermal rating:

926.2 Btu/hr maximum

MTBF rating

367 634 hr

Connector type

Performance specifications

Aggregate throughput

8.5 Gbps

The following table provides power data for an 8648GBRS module filled
with short-range SFPs. For power additions for middle and long-range
SFPs, see

“SFPs, XFPs, R and RS modules, and power consumption”

(page 66)

Table 66
8648GBRS power specifications-including short range SFP power

Specification

Value

3.3 V power (W)

110.8

12 V power (W)

160.8

Total power (W)

271.6

8648GTR module

The following table lists specifications for the 8648GTRS module.

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Summary of Contents for Passport 8600 Series































































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Nortel Passport 8600 Series, Installation Manual, Page: 132 / 164

Search results

Summary of Contents for Passport 8600 Series

Reviews: