manualshive.com logo in svg

Nortel Passport 8600 Series, Installation Manual, Page: 149 / 164

Share
Download
Nortel Passport 8600 Series Installation Manual Download Page 149

Port density for Ethernet Routing Switch 8600 modules

149

Table 93
Port density for Ethernet Routing Switch 8600 modules (cont’d.)

Maximum number of ports for each chassis

Module type

Port type

8003

8006

8010 and 8010co

10GBASE-SR

Not supported

12

24

10GBASE-LR

Not supported

12

24

10GBASE-LRM

Not supported

12

24

10GBASE-ER

Not supported

12

24

8683XLR

10GBASE-ZR

1

Not supported

4 with standard
fan tray; 12
with high speed
cooling module

8 with standard fan
tray; 24 with high speed
cooling module

10GBASE-SR

Not supported

12

24

10GBASE-LR/L
W

Not supported

12

24

10GBASE-LRM

Not supported

12

24

10GBASE-ER/
EW

Not supported

12

24

8683XZR

10GBASE-ZR/
ZW

1

Not supported

4 with standard
fan tray; 12
with high speed
cooling module

8 with standard fan
tray; 24 with high speed
cooling module

1

Nortel recommends that you install only one 10GBASE-ZR/ZW XFP in

one 8683XLR module due to cooling limitations on the 8683XLR and
XZR when using standard fan trays. Nortel further recommends that you
install the XFP only in Port 1. You can install a 10GBASE-SR, -LR/LW, or
-ER/EW in one or both of the remaining ports.

There are no XFP limitations when using high-speed cooling modules.

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Copyright © 2008 Nortel Networks

.

Summary of Contents for Passport 8600 Series





































































































































































Reviews:

No comments