Nortel Passport 8600 Series Installation Manual Download Page 137

Page: 137 / 164

8660 SDM

137

Table 74
8683XZR module specifications (cont’d.)

Electrical specifications

Data rate and encoding

10.3125 Gbps (LAN) or 9.953 Gbps
(WAN) with 64B/66B encoding

Compatible with STM-64

Module performance
(64 byte packets)

Aggregate throughput

3 x 14 880 952 pps

Routing and switching forwarding
rates

14 880 952 pps

Connector type

LC Duplex

The following table provides power specifications.

Table 75
8683XLR power specifications-including short-range XFPs

Specification

Value

3.3 V power (W)

80.9

12 V power (W)

90.0

Total power (W)

170.9

8660 SDM

Some 8660 Services Delivery Module specifications are found in the
following table; for more details, see Nortel Ethernet Routing Switch 8600
Installation — 8660 Service Delivery Module, NN46205-301.

Table 76
8660 SDM module specifications

Physical specifications

Height:

1.5 in. (3.8 cm)

Width:

15.4 in. (39.1 cm)

Depth:

18.5 in. (47.0 cm)

Weight:

11.0 lb (5.0 kg)

Electrical specifications

Input power:

140.0 W maximum. See the
following table.

Thermal rating:

477.4 Btu/hr maximum

MTBF rating

322 059 hr at 25 C

The following table provides power specifications for the 8660 SDM.

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Summary of Contents for Passport 8600 Series































































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Nortel Passport 8600 Series, Installation Manual, Page: 137 / 164

Search results

Summary of Contents for Passport 8600 Series

Reviews: