Nortel Passport 8600 Series Installation Manual Download Page 19

Page: 19 / 164

New in this release

The following sections detail what’s new in Nortel Ethernet Routing Switch
8600 Installation — Modules, NN46205-304 for Release 5.0.

•

“Features” (page 19)

•

“Other changes” (page 19)

Features

See the following section for information about feature changes:

RS modules

Release 5.0 introduces four new modules, termed RS modules. See

“Release 5.x module feature set” (page 26)

, and:

•

“8612XLRS module” (page 56)

and

Table 59 "8612XLRS module

specifications" (page 129)

•

“8634XGRS module” (page 58)

and

Table 63 "8634XGRS module

specifications" (page 131)

•

“8648GBRS module” (page 61)

and

Table 65 "8648GBRS module

specifications" (page 132)

•

“8648GTRS module” (page 62)

and

Table 70 "8648GTRS module

specifications" (page 134)

Other changes

See the following sections for information about changes that are not
feature-related:

Modules and power information

Information about SFP and XFP power consumption is added to

“SFPs,

XFPs, R and RS modules, and power consumption” (page 66)

. As well,

power specifications are updated for most modules. See

“Technical

specifications” (page 113)

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Summary of Contents for Passport 8600 Series































































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Nortel Passport 8600 Series, Installation Manual, Page: 19 / 164

Search results

Summary of Contents for Passport 8600 Series

Reviews: