manualshive.com logo in svg

Nortel Passport 8600 Series, Installation Manual, Page: 56 / 164

Share
Download
Nortel Passport 8600 Series Installation Manual Download Page 56

56

Ethernet Routing Switch 8600 module fundamentals

The following table describes the 8683XZR module LEDs.

Table 14
8683XZR module LEDs

Type

Label

Color, State

Meaning

Green, Steady

The port is enabled but not transmitting
data.

Green, Blinking

The port is transmitting data.

TX

Off

The port is disabled.

Green, Steady

The port is linked and enabled.

Green, Blinking

The port is receiving data.

Port

RX

Amber, Steady

The cable is disconnected, the port is
disabled, or the link is down.

Green, Steady

The module has completed the power-on
self-test and software initialization and is
operating normally.

Amber, Steady

The module slot is disabled.

Module

Online

Off

The module power is off. If the switch
power is on, the module is performing
the power-on self-test and software
initialization. A module in this state is not
yet functional.

The 8683XZR module supports R and M mode.

8612XLRS module

The 8612XLRS module is a 12-port XFP baseboard. This module supports
twelve 10 Gbps ports: four for each lane. All RS modules require the
high-speed cooling module. The following figure shows the 8612XLRS.

Figure 28
8612XLRS module

If you install 10GBASE-ER/EW or 10GBASE-ZR/ZW XFPs, to ensure
proper switch operation you must also install the 8005 Power Supply.

For a list of Nortel-qualified XFPs, see

“Nortel-qualified SFPs, XFPs, and

GBICs” (page 64)

.

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Copyright © 2008 Nortel Networks

.

Summary of Contents for Passport 8600 Series





































































































































































Reviews:

No comments