Nortel Passport 8600 Series Installation Manual Download Page 129

Page: 129 / 164

8612XLRS module

129

Table 58
8683POSM module specifications (cont’d.)

Cable specifications

single mode fiber optic cable:

9.3 mi (15 km) for OC-3c
connection

9.3 mi (15 km) for OC-12c
connection

Optical specifications

Wavelength:

OC-3c MDA SMF: 1274 to 1356 nm

OC-3c MDA MMF: 1274 to 1356 nm

OC-12c MDA SMF: 1274 to 1356 nm

OC-12c MDA MMF: 1260 to 1360 nm

Average transmit output power:

OC-3c and OC-12c MDAs SMF: -8 to
-15 dBm

OC-3c and OC-12c MDAs MMF: -14 to
-29 dBm

Average receiver sensitivity:

OC-3c MDA SMF: -14 to -28 dBm

OC-3c MDA MMF: -14 to -29 dBm

OC-12c MDA SMF: -7 to -18 dBm

OC-12c MDA MMF: -14 to -28 dBm

8612XLRS module

The following table describes the 8612XLRS module specifications.

Table 59
8612XLRS module specifications

Physical specifications

Height:

1.5 in. (3.8 cm)

Width:

15.4 in. (39.1 cm)

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Summary of Contents for Passport 8600 Series































































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Nortel Passport 8600 Series, Installation Manual, Page: 129 / 164

Search results

Summary of Contents for Passport 8600 Series

Reviews: