manualshive.com logo in svg

Nortel Passport 8600 Series, Installation Manual, Page: 113 / 164

Share
Download
Nortel Passport 8600 Series Installation Manual Download Page 113

113

.

Technical specifications

This section provides technical specifications for the Ethernet Routing
Switch 8600 modules.

For technical specifications for SFPs, XFPs, and GBICs, see Nortel
Ethernet Routing Switch 8600 Installation — SFP, XFP, OADM, and GBIC
Hardware Components, NN46205-320.

Navigation

•

“General specifications” (page 114)

•

“8608GBE and 8608GBM modules” (page 117)

•

“8608GTE and 8608GTM modules” (page 117)

•

“8608SXE module” (page 119)

•

“8616GTE module” (page 120)

•

“8616SXE module” (page 121)

•

“8624FXE module” (page 123)

•

“8632TXE and 8632TXM modules” (page 124)

•

“8648TXE and 8648TXM modules” (page 125)

•

“8672ATME and 8672ATMM modules” (page 126)

•

“8683POSM module” (page 128)

•

“8612XLRS module” (page 129)

•

“8630GBR module” (page 130)

•

“8634XGRS module” (page 131)

•

“8648GBRS module” (page 132)

•

“8648GTR module” (page 132)

•

“8648GTRS module” (page 134)

•

“8683XLR module” (page 135)

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Copyright © 2008 Nortel Networks

.

Summary of Contents for Passport 8600 Series





































































































































































Reviews:

No comments