Nortel Passport 8600 Series Installation Manual Download Page 125

Page: 125 / 164

8648TXE and 8648TXM modules

125

Table 53
8632TXE and 8632TXM module specifications (cont’d.)

Electrical specifications

MTBF rating

217 744 hr

Connector type

RJ-45 connector wired as MDI-X

SC duplex connectors on GBICs

Cable specifications

Type:

Category 3, 4, or 5 UTP cable (10
Mbps operation)

Category 5 UTP cable (100 Mbps
operation)

Maximum distance:

328 ft (100 m) for 10/100 Mbps ports

8648TXE and 8648TXM modules

The following table provides specifications for the 8648TXE and -M
modules.

Table 54
8648TXE and TXM module specifications

Physical specifications

Height:

1.5 in. (3.8 cm)

Width:

15.4 in. (39.1 cm)

Depth:

18.5 in. (47.0 cm)

Weight:

8.0 lb (3.6 kg)

Electrical specifications

Input power:

76 W maximum

Thermal rating:

261 Btu/hr maximum

MTBF rating

244 708 hr

Connector type

RJ-45 connector wired as MDI-X
(see )

Cable specifications

Type

Category 3, 4, or 5 UTP cable (10
Mbps operation)

Category 5 UTP cable (100 Mbps
operation)

Maximum distance

328 ft (100 m)

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Summary of Contents for Passport 8600 Series































































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Nortel Passport 8600 Series, Installation Manual, Page: 125 / 164

Search results

Summary of Contents for Passport 8600 Series

Reviews: