Nortel Passport 8600 Series Installation Manual Download Page 119

Page: 119 / 164

8608SXE module

119

8608SXE module

The following table provides specifications for the 8608SXE modules.

Table 40
8608SXE specifications

Physical specifications

Height:

1.5 in. (3.8 cm)

Width:

15.4 in. (39.1 cm)

Depth:

18.5 in. (47.0 cm)

Weight:

8.0 lb (3.6 kg)

Electrical specifications

Input power:

112.8 W maximum

Thermal rating:

384.6 Btu/hr maximum

MTBF rating

197 887 hr

Connector type

Duplex SC

The following table provides power specifications.

Table 41
8608SXE power specifications

Specification

Value

3.3 V power (W)

82.8

12 V power (W)

30.0

Total power (W)

112.8

The following table provides cable specifications.

Table 42
8608SXE cable specifications

Cable specifications

Type:

62.5 µm or 50 µm multimode fiber
optic cable

Maximum distance:

62.5 µm multimode fiber optic
cable:

•

722 ft (220 m) @ 160 MHz-km
bandwidth

•

902 ft (275 m) @ 200 MHz-km
bandwidth

50 µm multimode fiber optic cable:

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Summary of Contents for Passport 8600 Series































































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Nortel Passport 8600 Series, Installation Manual, Page: 119 / 164

Search results

Summary of Contents for Passport 8600 Series

Reviews: