Nortel Passport 8600 Series Installation Manual Download Page 130

Page: 130 / 164

130

Technical specifications

Table 59
8612XLRS module specifications (cont’d.)

Physical specifications

Depth:

18.5 in. (47.0 cm)

Weight:

10 lb (4.54 kg)

Electrical specifications

Input power:

257.9 W maximum (includes XFPs).
See the following tables.

Thermal rating:

879.44 Btu/hr maximum

MTBF rating

350 814 hr

Connector type

XFP—LC (fiber)

Performance specifications

Line rate

10.3125 Gbps (LAN data rate),
9.953 Gbps (WAN data rate)

The following table provides power data for an 8612XLRS module filled
with short-range XFPs. For power additions for middle and long-range
XFPs, see

“SFPs, XFPs, R and RS modules, and power consumption”

(page 66)

Table 60
8612XLRS power specifications-including short range XFP power

Specification

Value

3.3 V power (W)

80.3

12 V power (W)

177.6

Total power (W)

257.9

8630GBR module

The following table describes the 8630GBR module specifications.

Table 61
8630GBR module specifications

Physical specifications

Height:

1.5 in. (3.8 cm)

Width:

15.4 in. (39.1 cm)

Depth:

18.5 in. (47.0 cm)

Weight:

8.0 lb (3.6 kg)

Electrical specifications

Input power:

180.1 W maximum (includes SFPs).
See the following table.

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Summary of Contents for Passport 8600 Series































































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Nortel Passport 8600 Series, Installation Manual, Page: 130 / 164

Search results

Summary of Contents for Passport 8600 Series

Reviews: