Nortel Passport 8600 Series Installation Manual Download Page 136

Page: 136 / 164

136

Technical specifications

Table 72
8683XLR module specifications (cont’d.)

Electrical specifications

Thermal rating:

572.5 BTU/hr maximum

MTBF rating

184 230 hr

Data rate and encoding

10.3125 Gbps with 64B/66B
encoding

Compatible with STM-64

Module performance (64 byte packets)

Aggregate throughput

3 x 14 880 952 pps

Routing and switching forwarding
rates

14 880 952 pps

Connector type

LC Duplex

The following table provides power specifications.

Table 73
8683XLR power specifications-including short-range XFPs

Specification

Value

3.3 V power (W)

77.9

12 V power (W)

90.0

Total power (W)

167.9

8683XZR module

The following table describes the 8683XZR module specifications.

Table 74
8683XZR module specifications

Physical specifications

Height:

1.5 in. (3.8 cm)

Width:

15.4 in. (39.1 cm)

Depth:

18.5 in. (47.0 cm)

Weight:

8.0 lb (3.6 kg)

Electrical specifications

Input power:

170.9 W maximum (includes XFPs).
See the following tables.

Thermal rating:

582.8 Btu/hr maximum

MTBF rating

184 230 hr

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Summary of Contents for Passport 8600 Series































































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Nortel Passport 8600 Series, Installation Manual, Page: 136 / 164

Search results

Summary of Contents for Passport 8600 Series

Reviews: