manualshive.com logo in svg

Nortel Passport 8600 Series, Installation Manual, Page: 164 / 164

Share
Download
Nortel Passport 8600 Series Installation Manual Download Page 164

Nortel Ethernet Routing Switch 8600

Installation — Modules

Copyright © 2008 Nortel Networks
All Rights Reserved.

Printed in Canada and the United States of America
Release:

5.0

Publication:

NN46205-304

Document status:

Standard

Document revision:

02.02

Document release date:

16 June 2008

To provide feedback or to report a problem in this document, go to

www.nortel.com/documentfeedback.

www.nortel.com

LEGAL NOTICE

While the information in this document is believed to be accurate and reliable, except as otherwise expressly agreed to in writing
NORTEL PROVIDES THIS DOCUMENT "AS IS" WITHOUT WARRANTY OR CONDITION OF ANY KIND, EITHER EXPRESS
OR IMPLIED. The information and/or products described in this document are subject to change without notice.

Nortel, the Nortel logo, the Globemark, and Passport are trademarks of Nortel Networks.

Velcro is a trademark of Velcro Industries B.V.

PowerPC is a trademark of International Business Machines Corp.

All other trademarks are the property of their respective owners.

ATTENTION

For information about the regulatory and safety precautions, read "Regulatory Messages and Safety
Precautions" in this guide.

For a list of safety messages and their translations, see "Translations of Safety Messages" in this
document.

Summary of Contents for Passport 8600 Series





































































































































































Reviews:

No comments