Nortel Passport 8600 Series Installation Manual Download Page 124

Page: 124 / 164

124

Technical specifications

Table 51
8624FXE specifications (cont’d.)

Optical specifications

Transmitter characteristics:

Minimum optical power: -19 dBm

Maximum optical power: -14 dBm

Receiver characteristics:

Minimum receiver sensitivity: -34
dBm

Maximum input power: -14 dBm

The following table provides power specifications.

Table 52
8616FXE power specifications

Specification

Value

3.3 V power (W)

64.4

12 V power (W)

20.4

Total power (W)

84.8

8632TXE and 8632TXM modules

The following table provides specifications for the 8632TXE and -M
modules.

Table 53
8632TXE and 8632TXM module specifications

Physical specifications

Height:

1.5 in. (3.8 cm)

Width:

15.4 in. (39.1 cm)

Depth:

18.5 in. (47.0 cm)

Weight:

9 lb (4 kg)

Electrical specifications

Input power:

100 W maximum

Thermal rating:

193 Btu/hr maximum

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Summary of Contents for Passport 8600 Series































































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Nortel Passport 8600 Series, Installation Manual, Page: 124 / 164

Search results

Summary of Contents for Passport 8600 Series

Reviews: