Nortel Passport 8600 Series Installation Manual Download Page 141

Page: 141 / 164

8691 SF/CPU module

141

Table 83
8691 SF/CPU module specifications (cont’d.)

Physical specifications

Depth:

18.5 in. (47.0 cm)

Weight:

7.2 lb (3.3 kg)

Electrical specifications

Input power:

91.9 W (113.4 W with Mezz)
maximum. See the following table.

Thermal rating:

313.4 (386.7) Btu/hr maximum

MTBF rating

213 454 hr

Connector types

Ethernet Management port:

RJ-45 connector wired as MDI (see )

Console port:

DB-9 connector (see

“8691 SF/CPU

Management port” (page 141)

)

Modem port:

DB-9 connector (see

“8691 SF/CPU

Console port” (page 142)

)

Cable specifications

Ethernet Management port:

Category 3, 4, or 5 UTP cable (10
Mbps operation)

Category 5 UTP cable (100 Mbps
operation)

Console port:

RS-232 cable

Modem port:

DTE-to-DCE cable (straight or
transmit cable)

The following table provides power specifications for the 8691 SF/CPU
module.

Table 84
8691 SF/CPU power specifications

Specification

Without Mezz

With Mezz

3.3 V power (W)

43.9

59.4

12 V power (W)

48.0

54.0

Total power (W)

91.9

113.4

8691 SF/CPU Management port

The Management port is a 10/100 Mbps Ethernet port implemented on an
RJ-45 connector wired as an MDI connection. (see the following table).

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Summary of Contents for Passport 8600 Series































































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Nortel Passport 8600 Series, Installation Manual, Page: 141 / 164

Search results

Summary of Contents for Passport 8600 Series

Reviews: