manualshive.com logo in svg

Nortel Passport 8600 Series, Installation Manual, Page: 54 / 164

Share
Download
Nortel Passport 8600 Series Installation Manual Download Page 54

54

Ethernet Routing Switch 8600 module fundamentals

Table 13
8683XLR module LEDs

Type

Label

Color, State

Meaning

Green, Steady

The port is enabled but not transmitting
data.

Green, Blinking

The port is transmitting data.

TX

Off

The cable is disconnected or the link is
down.

Green, Steady

The port has a link and is enabled.

Green, Blinking

The port is receiving data.

RX

Off

The cable is disconnected or the link is
down.

Port

TX and RX

Both Blinking Green

The port is disabled.

Green, Steady

The module has completed the
power-on self-test and software
initialization and is operating normally.

Amber, Steady

The module slot is disabled or initializing
the software.

Module

Online

Off

The switch power is off or there is no
power to the module. If the switch
power is on, the module is performing
the power-on self-test and software
initialization. A module in this state is not
yet functional.

For a description of how to configure the 8683XLR module, see Nortel
Ethernet Routing Switch 8600 Configuration — Ethernet Modules,
NN46205-503.

The Ethernet Routing Switch 8600 8683XLR module is an R module and
supports:

•

256 000 IP routes

•

64 000 MAC records

•

Release 4.1 and earlier: 16 000 in R mode
Release 5.0 and later: 32 000 in R mode

The 8683XLR module supports R and M mode.

8683XZR module

The 868XZR module supports both LAN and WAN operation (10.3 Gbps
LAN PHY and 9.9 Gbps WAN PHY). The 8683XZR module provides three
bays for XFP transceivers. The port operates in full-duplex mode. The
following figure shows the 8683XZR.

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Copyright © 2008 Nortel Networks

.

Summary of Contents for Passport 8600 Series





































































































































































Reviews:

No comments