manualshive.com logo in svg

Nortel Passport 8600 Series, Installation Manual, Page: 36 / 164

Share
Download
Nortel Passport 8600 Series Installation Manual Download Page 36

36

Ethernet Routing Switch 8600 module fundamentals

Table 3
8608SXE module LEDs

Type

Label

Color, State

Meaning

Green, Blinking

The port is transmitting data.

Amber, Steady

A fault condition exists on the line or on the
attached remote device.

TX

Off

The port has not detected a fault condition.

Green, Steady

The port is linked and enabled.

Green, Blinking

The port is receiving data.

Amber, Steady

The port has either no optical signal or no
link synchronization.

Port

RX

Off

The port has a signal, but no link.

Green, Steady

The module has completed the power-on
self-test and software initialization and is
operating normally.

Amber, Steady

The module failed the power-on self-test.

Module

Online

Off

The module power is off. If the switch
power is on, the module is performing
the power-on self-test and software
initialization. A module in this state is not
yet functional.

The 8608SXE module supports up to 32 000 table entries in its forwarding
engine. The 8608SXE module does not support R or M mode.

8616GTE module

The 8616GTE module provides 16 1000BASE-T copper gigabit Ethernet
ports with 8-pin modular (RJ-45) connectors. Each port operates in 1000
Mbps full-duplex mode and supports the IEEE 802.3ae standard. You can
attain distances of up to 100 meters with CAT 5 unshielded twisted pair
(UTP) cable. The following figure shows the 8616GTE module.

Figure 8
8616GTE module

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Copyright © 2008 Nortel Networks

.

Summary of Contents for Passport 8600 Series





































































































































































Reviews:

No comments