manualshive.com logo in svg

Nortel Passport 8600 Series, Installation Manual, Page: 38 / 164

Share
Download
Nortel Passport 8600 Series Installation Manual Download Page 38

38

Ethernet Routing Switch 8600 module fundamentals

When you use an 8616 module with Auto-Negotiation enabled, set the
re-autoneg flag for proper interoperability. Set the flag using the CLI
command

config bootconfig flags 8616-reautoneg true

or the

NNCLI command

boot config flags 8616-reautoneg

.

8616SXE module

The 8616SXE module provides 16 1000BASE-SX ports (850 nm Gigabit
Ethernet) that use MT-RJ type connectors for riser connections, server
attachments, or interswitch links. The 8616SXE module supports
standards-based 1000 Mbps (1 Gbps) full-duplex operation only. The
following figure shows the 8616SXE module.

Figure 10
8616SXE module

The optical transceivers provide transmission ranges as follows:

•

up to 275 m using 62.5 µm multimode fiber cable

•

up to 550 m using 50 µm multimode fiber cable

The following figure shows the location of the 8616SXE module LEDs.

Figure 11
8616SXE module LEDs

The following table provides a description of the 8616SXE module LEDs.

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Copyright © 2008 Nortel Networks

.

Summary of Contents for Passport 8600 Series





































































































































































Reviews:

No comments