manualshive.com logo in svg

Nortel Passport 8600 Series, Installation Manual, Page: 41 / 164

Share
Download
Nortel Passport 8600 Series Installation Manual Download Page 41

Interface module descriptions

41

Type

Label

Color, State

Meaning

Amber, Blinking

A fault condition exists at the far end of
the connection, and the port is sending or
receiving.

Off

The port is not connected; or is connected but
has no link.

Green, Steady

The module has completed the power-on
self-test and software initialization and is
operating normally.

Amber, Steady

The module failed the power-on self-test.

Module

Online

Off

The module power is off. If the switch power
is on, the module is performing the power-on
self-test and software initialization. A module
in this state is not yet functional.

The 8624FXE module supports up to 32 000 table entries in its forwarding
engine.

The 8624FXE module does not support R or M mode.

8632TXE and 8632TXM modules

The 8632TXE and 8632TXM modules provide 32 autonegotiating
10BASE-T/100BASE-TX ports that use 8-pin modular (RJ-45) connectors.
Ports operate at either 10 Mbps or 100 Mbps up to distances of 100 m with
CAT 3 or better unshielded twisted pair (UTP) cable. The following figure
shows the 8632TXE or 8632TXM module.

Figure 14
8632TXE or 8632TXM module

Two bays are provided for 1000BASE-X GBICs.

The 8632TXE and 8632TXM module ports support the IEEE 802.3 1998
Clause 28 Auto-Negotiation standard. Each port can operate in full- or
half-duplex mode. When a port is connected to another device that also

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Copyright © 2008 Nortel Networks

.

Summary of Contents for Passport 8600 Series





































































































































































Reviews:

No comments