Nortel Passport 8600 Series Installation Manual Download Page 35 | Manualshive

Page: 35 / 164

Nortel Passport 8600 Series Installation Manual Download Page 35

Interface module descriptions

35

8608SXE module

The 8608SXE module supports eight 1000BASE-SX ports (850 nanometer
[nm] Gigabit Ethernet) that use SC connectors for riser connections,
server attachments, or interswitch links. The 8608SXE module supports
standards-based 1000 Mbps (1 Gbps) full-duplex operation only. The
following figure shows the 8608SXE module.

Figure 6
8608SXE module

The optical transceiver provides transmission ranges as follows:

•

Up to 275 meters (m) using 62.5 micrometer (µm) multimode fiber
cable

•

Up to 550 m using 50 µm multimode fiber cable

The following figure shows the location of the 8608SXE module LEDs.

Figure 7
8608SXE module LEDs

The following table describes the 8608SXE module LEDs.

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Copyright © 2008 Nortel Networks

.

«
...
33
34
35
36
37
...
»

Summary of Contents for Passport 8600 Series





































































































































































Reviews:

No comments