LG-Ericsson iPECS eMG100 Programming Manual Download

Page: 64 / 718

iPECS eMG80/100& eMG800 & UCP & vUCP
Administration and Programming Manual

Issue 2.3

Table 3.3.3.3-1 STATION ISDN ATTRIBUTES (PGM 114)

BTN

ATTRIBUTE/DISPLAY

DESCRIPTION

RANGE

DEFAULT

100-110 COLR SERVICE

(1:ON/0:OFF ) : OFF

COLR (Connected Line Id Restriction), an

ISDN service, removes connected party Id

sent from the PSTN to the calling party with

a RESTRICT instruction in the CONNECT

message.

If enabled here, the system will send the

restrict instruction to the PSTN when the

station answers an ISDN call.

0: OFF

1: ON

OFF

100-110 STN CLI 1

100

When not restricted (button 4 & 5 above)

and entry 00 of the CLIP/CLOP Table is

selected in PGM 143-button 1& 2, this entry

is added to the number sent in the ISDN

call SETUP or CONNECT message in

place of the station number.

12 digits

Station

number

100-110 3.1 kHz AUDIO

(1:ON/0:OFF ) : OFF

When an analog device (SLT or FAX) uses

an ISDN Line in the system, the Information

Element of the ISDN SETUP message

must indicate it only has 3.1 KHz audio

capabilities. If a SLT or analog FAX will be

allowed access to the ISDN Lines, this
parameter must be “ON”.

0: OFF

1: ON

OFF

100-110 CLI NAME DISP

(1:ON/0:OFF ) : OFF

When the CLI data from the PSTN in the

call SETUP message matches a number in

Speed Dial, the system can display the

name associated with the Speed Dial bin, if

set to ON.

0: OFF

1: ON

OFF

100-110 CLI/REDIRECT

(1:RED/0:CLI) : CLI

When an incoming ISDN call is Redirected

by the ISDN, the call SETUP message will

contain an original and redirected CLI. This

selection determines if the iPECS Phone

will display the original or redirected

number.

0: CLI

1: Redirect

CLI

100-110 CLI MSG-WAIT

(1:ON/0:OFF ) : OFF

A log of caller identification canbe

maintained for the user,permitting the user

to call backthe identified party.

System-wide, up to 1000 entriescan be

maintained in the log.

0: OFF

1: ON

OFF

100-110 EXTOR ATD

(1:ATD/0:EXT ) : EXT

When the system sends astation number

with CLIP orCOLP, the number can be

eitherthe Attendant number or thenumber

of the station.

0: EXT

1: ATD

EXT

Summary of Contents for iPECS eMG100















































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for iPECS eMG100

Reviews:

Related manuals for iPECS eMG100

Brands by name

Popular brands

LG-Ericsson iPECS eMG100, Programming Manual

Search results

Summary of Contents for iPECS eMG100

Reviews:

Related manuals for iPECS eMG100

Brands by name

Popular brands