LG-Ericsson iPECS eMG100 Programming Manual Download Page 558

Page: 558 / 718

iPECS eMG80/100& eMG800 & UCP & vUCP
Administration and Programming Manual

Issue 2.3

541

Table 4.4.11.2-1 H.323 CO Group Attributes

ATTRIBUTE

DESCRIPTION

RANGE

DEFAULT

H.323 DTMF Path

During a connection, DTMF Digits can be sent in-band or

out of band (H.245).

IN, RFC2833, H245_ALNUM, H225_SIG, H245_SIG

Refer to

description

TCP Keep Alive

The system will send a polling message every 75 seconds

to assure the status of the TCP connection.

OFF

TCP No Delay

Normally small chunks of TCP (H323) messages are

combined into one packet and be sent to remote party to

improve the efficiency of network. Sometimes this action

yields the H323 signaling problem when system is behind

NAT router and there is H323 ALG is running. 'OFF' value

can be a solution to overcome the problem.

OFF

Sending Setup Ack

message

System provides SETUP ACK message when there is
no‘sending complete IE’ in SETUP message.

OFF

Firewall IP Address Enter the firewall IP Address.

Gatekeeper Attributes

RAS Usage

Determine whether VOIU/VOIB/VOIM will be used as a

Gatekeeper.

OFF

RAS MultiCast IP

Port

Multi-cast IP Port for RAS Information of Gatekeeper.

1~65535

1718

RAS MultiCast IP

Address

Multi-cast IP address for RAS Information of Gatekeeper.

IP Address 224.0.1.41

RAS UniCast IP

Port

Uni-cast IP Port for RAS Information of Gatekeeper.

1~65535

1719

RAS UniCast IP

Address

Uni-cast IP address for RAS Information of Gatekeeper.

IP Address 82.134.80.2

RAS Keep Alive

Time

The time between exchange of RAS Information between

GK and VOIB/VOIU.

001-999

(SEC)

120

RAS IIR Multiplier

Ratio

This feature is used when H323 call is routed by RAS

gatekeeper. Keep alive interval time between the system

and gatekeeper is provided by gatekeeper on registration

time. This value of ratio is used to change the keep alive

interval time from gatekeeper.

10~100%

RAS Number Plan

Prefix

The numbering plan for Calling Number in RAS Setup.

Max. 23

digits

RAS Light RRQ

usage

The Gatekeeper ID (This can be programmed only via WEB

Admin).

OFF

RAS Gateway ID

The system can be assigned to use the simple RRQ

(Registration Request) message (ON) or the full RRQ

message (OFF).

Max. 128

characters

Fail over Usage

The H.323 call will be failover to another line (FAIL OVER

USAGE: ON).

OFF

Call Setup No

Response time

The H.323 call will be failover. The time will be set.

0, 3-15

(Sec.)

Summary of Contents for iPECS eMG100















































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for iPECS eMG100

Reviews:

Brands by name

Popular brands

LG-Ericsson iPECS eMG100, Programming Manual

Search results

Summary of Contents for iPECS eMG100

Reviews:

Brands by name

Popular brands