manualshive.com logo in svg

LG-Ericsson iPECS eMG100, Programming Manual

Share
Download
LG-Ericsson iPECS eMG100 Programming Manual Download Page 281

iPECS eMG80/100& eMG800 & UCP & vUCP 
Administration and Programming Manual 

Issue 2.3 

264 

Table 4.4.2.2-1 Common Attributes 

ATTRIBUTE 

DESCRIPTION 

RANGE 

DEFAULT 

Left Message 

to Executive 

When a call forwards to the Secretary of anExecutive/Secretary 

pair, messages can be left for theExecutive (ON) or Secretary 

(OFF). 

OFF 

ON 

ON 

Station Web 

Level 

Based on this level, the user will be able to view the specified 

programs within the Station User Web portal. Level 1 can view all 

programs, Levels 2 and 3 are configured in the title 

“System data: 

Station Web Authorization”. This is a Web only PGM. 

LEVEL 1 ~ 

LEVEL 3 

LEVEL 2 

Headset page 

mode 

When a page announcement is received, it is normally played 

over the Speaker of the iPECS IP or LDP Phone. For headset 

users, the page can played to the headset or both the headset 

and speaker.

SPKR, HEADSET, BOTH

 

Refer to 

description 

Speaker 

Progress 

Indication 

When employing a non-ISDN terminal, specifically a modem or 

analog FAX, the ISDN call SETUP message must include this 

message and 

“Progress Indication” should be set to “ON”. 

OFF 

ON 

OFF 

3.1 KHz Audio 

When an analog device (SLT or FAX) uses an ISDNLine in the 

system, the Information Element of theISDN SETUP message 

must indicate the device onlyhas 3.1 KHz audio capabilities. If an 

SLT or analogFAX will be allowed access to the ISDN Lines, 
thisparameter must be “ON” 

OFF 

ON 

OFF 

Pickup by 

flexible button 

When a station receives a call, the DSS/BLF button at other 

stations will flash and, if allowed, other stations may use the 

button to answer (pick-up) the call. 

ON:

User can pick up by DSS button.   

OFF:

 User can

’t pickup by DSS button. 

OFF 

ON 

ON 

Prepaid Call   

It is useful feature for user to pay the money within the budget 

(Prepaid) for outgoing calls. For more information, refer to the 

below feature 

“Prepaid money”. 

OFF 

ON 

OFF 

Prepaid Money   

(0 - 999999) 

& 

Used Prepaid 

Money 

An amount can be associated with the station as prepayment for 
outgoing calls. The assigned “Pre-paid Money” is reduced by the 

calculated call cost (Call Metering or cost/minute). This parameter 

displays the remaining funds for outgoing calls. Prepaid Money is 

often used in small hospitality businesses. 

The 

“Used Pre-paid Money” displays the money that has been 

used. 

000000 

– 

999999 

 

000000 - 

999999 

0 

 

 

0 

SIP USER 

TABLE INDEX 

These fields reference the index to the SIP User ID Attributes 

Table. The referenced SIP User ID may be employed for several 

of the SIP headers for outgoing calls and may be employed for 

incoming call routing as configured in the SIP CO Attributes PGM 
133, “ID Assigned Station”. 

Up to three SIP User Id indices can be assigned to each station to 

permit the use of up to three SIP Trunk service providers. 

eMG80/100:0~140, eMG800:0~1200, UCP:0~2400 

Refer to 

description 

0 

SIP USER 

TABLE 

INDEX2 

0 

SIP USER 

TABLE 

INDEX3 

0 

Summary of Contents for iPECS eMG100















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands