manualshive.com logo in svg

LG-Ericsson iPECS eMG100, Programming Manual

The LG-Ericsson iPECS eMG100 is a highly efficient and innovative business communication system. Unlock its full potential with our comprehensive Programming Manual, available for free download on manualshive.com. This manual provides detailed instructions and insights to maximize the functionality of your device.

Share
Download
background image

iPECS eMG80/100& eMG800 & UCP & vUCP 
Administration and Programming Manual 

Issue 2.3 

96 

3.3.5.10  T1 Line Timers 

– PGM 152 

North American T1 standards require that the T1 terminating device, in this case the iPECS eMG, include 
various “adjustable” timers and counters as described below. 

PROCEDURE 

 

COL T1 ATT 

ENTER CO RANGE 

Press the 

[PGM] 

button and dial 152. 

01-02 COL T1 ATT 

PRESS FLEX KEY (01-13) 

Use the dial-pad to enter a CO Line range (Ex. 01-02). For a single CO Line, 

enter the same number twice.   

Press the desired Flex button; refer to Table 3.3.5.10-1. 

Use the dial-pad to enter desired data for the Attribute, refer to Table 

3.3.5.10-1. 

Press the 

[Save] 

button to store the data entry. 

 

Table 3.3.5.10-1 T1 LINE TIMERS (PGM 152) 

BTN 

ATTRIBUTE/DISPLAY 

DESCRIPTION 

RANGE 

DEFAULT 

1 

01-02 PAUSE 

(1-9) : 2 (sec) 

A timed pause may be included in a Speed 

Dial number, in which case, the pause time is 

defined by this entry.Not currently 

implemented. 

1~9 

(seconds) 

2 

2 

01-02 RLS GRD 

(01-60) : 20 (100ms) 

The releaseguard timer defines the length of 

time the system will maintain a Line as busy 

after the call has been terminated to assure 
the PSTN has sufficient time to ‘clear down’ 

the circuit. Not currently implemented. 

01~60 

(100 ms) 

20 

3 

01-02 DT DELAY 

(02-50) : 10 (100ms) 

The DT (Dial tone) Delay timer defines the 

duration that dial tone must be received for 

DT recognition. 

Not currently implemented. 

02~50 

(100 ms) 

10 

4 

01-02 INTER DGT 

(15-30) : 15 (20ms) 

The Inter Digit timer defines the duration 

between digit transmissions. 

Not currently implemented. 

15~30 

(20 ms) 

15 

5 

01-02 WINK 

(07-15) : 10 (20ms) 

For TIE or DID Lines the Wink timer defines 
the length of time the ‘wink’ (T1 TIE line 

circuit reversal) will last. 

7~15 

(20 ms) 

10 

6 

01-02 OP RATE ( 0- 3) 

60-40 (10pps) (0) 

For Pulse signaling, defines the duration and 

make/break ratio of each pulse. 

0: 60-40(10pps), 1: 66-33(10pps) 
2: 60-40(20pps), 3: 66-33(20pps)

 

Refer to 

description 

60-40 

(10pps)

 

7 

01-02 SEZ DTC   

(000-127) : 003 (20ms) 

This timer defines the length of a valid ‘line 
seizure’ signal. 

0~127 

(20 ms) 

3 

Summary of Contents for iPECS eMG100















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for iPECS eMG100

Panasonic KXTGA820 - EXPND DIGITAL CORDLESS HANDSET Manual De Instalación preview
KXTGA820 - EXPND DIGITAL CORDLESS HANDSET
Brand: Panasonic Pages: 5
Yealink SIP-T18P User Manual preview
SIP-T18P
Brand: Yealink Pages: 21
Telos VSet1 Installation Instructions preview
VSet1
Brand: Telos Pages: 2
Uniden TRU 5865 Series Manual D'Utilisation preview
TRU 5865 Series
Brand: Uniden Pages: 60
Matosio BluePod Quick Start Manual preview
BluePod
Brand: Matosio Pages: 37
Telematrix MARQUIS 9600 Series User Manual preview
MARQUIS 9600 Series
Brand: Telematrix Pages: 30
Daewoo DTC-370 User Manual preview
DTC-370
Brand: Daewoo Pages: 33
Myria MY9082 User Manual preview
MY9082
Brand: Myria Pages: 32
3SIXT SNAP STICK User Manual preview
SNAP STICK
Brand: 3SIXT Pages: 6
Emerson EM6130 User Manual preview
EM6130
Brand: Emerson Pages: 2
Emerson EM6120-2 User Manual preview
EM6120-2
Brand: Emerson Pages: 28
Emerson EM7000 User Manual preview
EM7000
Brand: Emerson Pages: 1
AdvanceTec KYOCERA DuraPlus AT3082A  User Manual preview
KYOCERA DuraPlus AT3082A 
Brand: AdvanceTec Pages: 8
Uniden D2380 Series User Manual preview
D2380 Series
Brand: Uniden Pages: 24
Plantronics Stereo SupraPlus USB Configuration Manual preview
Stereo SupraPlus USB
Brand: Plantronics Pages: 2
Plantronics CT11 Quick Start User Manual preview
CT11
Brand: Plantronics Pages: 2
Plantronics Elara 60 WS User Manual preview
Elara 60 WS
Brand: Plantronics Pages: 13
Xact XG3400 Instruction Manual preview
XG3400
Brand: Xact Pages: 62

Brands by name

Popular brands

Load more brands