LG-Ericsson iPECS eMG100 Programming Manual Download

Page: 576 / 718

iPECS eMG80/100& eMG800 & UCP & vUCP
Administration and Programming Manual

Issue 2.3

559

Table 4.4.13.6-1 ZONE ATTRIBUTES

ATTRIBUTE

DESCRIPTION

RANGE

DEFAULT

Remark

Descriptive information to help installer/programmer in

identifying the device Zone, i.e. Branch1.

Max. 21

characters

Display time zone

The time & date displayed at the station are based on the

time zone selected or the system time

Time zone, System time

Refer to

description

System

time

Max Total Inter

Zone Connections

This parameter may be used to limit the number of

maximum Inter Zone connections. When this value is set to

0, there is no limit on the total Inter Zone connections.

eMG80/100:0-140, eMG800: 0-1200, UCP: 0-2400 (0: No

limit)

Refer to

description

Max Outgoing CO

Calls

This field may be used to limit the number of outgoing

CO/IP calls from the Zone. When this value is set to 0,

there is no limit on the number of outgoing CO/IP calls.

eMG80/100:0-74, eMG800: 0-600, UCP: 0-998 (0: No limit)

Refer to

description

Zone MOH Assign

A Music source can be assigned so that calls to this zone.

Refer to Sys Hold,Internal music, External Music,

VSFMOH,SLT MOH1~5,VSF MOH2~30

Refer to

description

Refer to

Sys Hold

Emergency Call

Notify Station

Assigns the destination station for Emergency Call

Notification.

Station

number

Emergency Call

Notify 2nd Station

This field assigns a secondary station to receive notification

of an Emergency call from a device in the Zone.

Station

number

DCOB Fault Notify

Station

This field assigns the station to receive notification of a

DCOB (Digital CO Board) fault.

Station

number

SIP Registration

Fault Notify Station

This field assigns the station to receive notification of a SIP

Trunk registration fault.

Station

number

Daylight Saving

Usage

If option is "System DST mode", the zone will follow the

system DST mode(System Date&Time(178)).If option is

"OFF", the zone will not apply the Daylight Saving Time.

System DST mode, OFF

Refer to

description

System

DST mode

Summary of Contents for iPECS eMG100















































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for iPECS eMG100

Reviews:

Related manuals for iPECS eMG100

Brands by name

Popular brands

LG-Ericsson iPECS eMG100, Programming Manual

Search results

Summary of Contents for iPECS eMG100

Reviews:

Related manuals for iPECS eMG100

Brands by name

Popular brands