LG-Ericsson iPECS eMG100 Programming Manual Download

Page: 452 / 718

iPECS eMG80/100& eMG800 & UCP & vUCP
Administration and Programming Manual

Issue 2.3

435

Table 4.4.6.3-3 RING GROUP ATTRIBUTES

ATTRIBUTE

DESCRIPTION

RANGE

DEFAULT

Maximum

Queued Call

Counter

When the number of calls queued to the group match this parameter,

new calls will receive error tone and be disconnected after the VSF

AA announcement, if assigned, is played.

00-99

Allow

Forward

Member

A member activating Call Forward may be placed in an unavailable

state for Station group calls (ON). When OFF, group calls are sent to

the member as normal.

OFF : no FWD, ON : FWD

Refer to

description

Group name A group name can be designated.

Max.12cha

racters

Mailbox

Message

Wait Station

When a call overflows or routes to the VM group, a station number is

used to identify the Mailbox for the group messages.

Station

number

Mailbox

Password

The password associated with the group Mailbox is defined here. The

password is used in conjunction with the group Mailbox as with a

normal station.

Max. 12

digits

Forced

Forward

Destination

Calls to a Station group may forward directly to a defined destination,
bypassing the hunt process. “Forced Forward”, below, must be

enabled.



STA/NET or Station group,



VSF Announcement,



Sys. Speed

Refer to

description

Forced

Forward Dest

Usage

Calls to a Station group may forward directly to a defined destination,
see above “Forced Forward Destination” when Forced Forward

isenabled for the group.

OFF

Ring group

indication

When a station calls a Ring Group, DSS/BLF buttons assigned for

the calling station will flash and muted ring is received.

OFF, ON (Ring and LED), ON (LED only)

Refer to

description

ON (Ring

and LED)

Ring Tone

When a call is routed to a group, programmed ring tone is served to

the group member.

00-16

(00:N/A)

Group Ring

Back Tone

When group member is ringing for group, The ring back tone can be

provided to the caller according to ring back tone for group.



Ring back tone

: ring back tone is provided when the member

for gropu is ringing



MOH

: MOH is provided when the member for group is ringing.



MOH (after connection)

: MOH is provided when system

answered the call

Refer to

description

Ring back

tone

Summary of Contents for iPECS eMG100















































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for iPECS eMG100

Reviews:

Related manuals for iPECS eMG100

Brands by name

Popular brands

LG-Ericsson iPECS eMG100, Programming Manual

Search results

Summary of Contents for iPECS eMG100

Reviews:

Related manuals for iPECS eMG100

Brands by name

Popular brands