manualshive.com logo in svg

LG-Ericsson iPECS eMG100, Programming Manual

Share
Download
LG-Ericsson iPECS eMG100 Programming Manual Download Page 224

iPECS eMG80/100& eMG800 & UCP & vUCP 
Administration and Programming Manual 

Issue 2.3 

207 

3.3.11.3  TNET LM ATTRIBUTES 

– PGM 332 

The CM (Central MPB/MPB) must be programmed with the MAC and IP address of each LM (Local MPB) in 
the Centralized Control network as well as the maximum configuration of each LM.   

The port counts define the ports, which are allocated in the CM database for use by devices registered to the 
LM.   

The number of ports defined in the database of each LM, seesPGM 331, must be equal to or less than the 
ports defined in the CM for the LM, in order to register properly.   

VoIP channels are needed to support RTP Packet relay or codec translation between other devices. The CO 
port count must include any VoIP channels required. 

PROCEDURE: 

 

TNET LM ATTRIBUTES 

ENTER BIN NO(01-15) 

Press the 

[PGM] 

button and dial 332. 

TNET LM(01) ATTRIBUTES 

PRESS FLEX KEY (1- 4) 

Use the dial pad to enter the bin number associated with the LM. 

Press the Flex button, 1~4 for the desired setting, refer to Table 3.3.11.3-1. 

Use the dial-pad to enter the required data, refer to Table 3.3.11.3-1. 

Press the 

[Save] 

button to store the new data. 

 

Table 3.3.11.3-1 TNET LM ATTRIBUTES (PGM 332) 

BTN 

ATTRIBUTE/DISPLAY 

DESCRIPTION 

RANGE 

DEFAULT 

1 

LM(01) MAC ADDRESS 

0000000000000 

This field defines the MAC address of the LM 

that will be part of the TNET environment and 

is used by the CM for authorization. 

MAC 

address 

 

2 

LM(01) IP ADDRESS 

0      .0      .0      .0 

This field displays the IP address of the LM. 

IPv4 

address 

 

3 

LM(01) IPKTS PORT 

(0001 - 9999) :5588 

In the TNET environment, the IP KTS 

protocol signaling UDP port is defined. At 

present this field is not used, do not change 

this port number. 

0000-9999  5588 

4 

LM (01) TOTAL PORT 

(000 

– 999) : 000 

This field defines the total number of ports the 

LM will request be allocated by the CM for 

devices attached to the LM. 

This value must be equal to or more than the 

available port count in the LM. 

000-999 

000 

5 

LM (01) MULTICAST IP 

239.20.19.1 

This field defines the multicast IP address 

that could be used in TNET branch site. 

IPv4 

address 

 

 
 

 

Summary of Contents for iPECS eMG100















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands