manualshive.com logo in svg

LG-Ericsson iPECS eMG100, Programming Manual

Share
Download
LG-Ericsson iPECS eMG100 Programming Manual Download Page 280

iPECS eMG80/100& eMG800 & UCP & vUCP 
Administration and Programming Manual 

Issue 2.3 

263 

Table 4.4.2.2-1 Common Attributes 

ATTRIBUTE 

DESCRIPTION 

RANGE 

DEFAULT 

Speed Dial 

Access 

Allows the station to access System Speed Dial bins. 

Disable 

Enable 

Enable 

Alarm/Door Bell  Assigns a station to receive Alarm/Door Bell signal. 

Disable 

Enable 

Disable 

Station Account   

When ON, the station user must enter an authorization code to 

access CO/IP Lines.   

OFF 

ON 

OFF 

Forced SMDR 

Account Code 

When On, the user must enter an Account code to place an 

outgoing call. 

OFF 

ON 

OFF 

Loop LCR 

Account 

The Station may be required to enter a StationAuthorization code 

to accessLOOP LCR operation. 

OFF 

ON 

OFF 

Door Open 

Enables use of Door open feature by station. 

Disable 

Enable 

Enable 

Flex Button 

PGM 

The ability to assign Flexible buttons of the iPECS IP and LDP 

Phones can be controlled. When allowed here, the user may 

assign features to Flexible buttons but requires special 

assignments to configure CO/IP Line buttons. 

OFF 

ON 

ON 

Prefer CO or 

Group 

The System will seize this CO/IP Line or a Line from the CO/IP 
group numberwhen the station dials “9” (First available Co 

accesscode) 

CO, IP Line, CO Groupnumber 

Refer to 

description 

Access 

code 

Emergency CO 

or Group   

This field defines the CO/IP Line or Group employed by the 

system to place Emergency Assistance calls.   

CO #, CO Group # 

Refer to 

description 

Any CO 

ICM Tenancy 

Group 

Assigns stations to an ICM Tenancy Group. 

eMG80/100:1~15, eMG800:0~32, UCP:0~100 

Refer to 

description 

1 

Call Time 

Restriction 

All outgoing calls will disconnect at expiration of theCall Restrict 

Timer. The Cut-Off Timers can be set the time for Station and CO 

Line. For cut off timer of Station, refer to the title 

“Station Timers 

(123)

”. For CO line, refer to the title “CO Line data: Common 

Attributes (144)

”. 

OFF 

ON 

OFF 

Proctor 

MonitoringPow

er-Fail 

Enables use of PABX ANI Link device for E-911support, Only an 

SLT port can be used for this feature. 

OFF 

ON 

OFF 

Line Release 

CostDisplay 

When a CO/IP line is released, the disconnect cause or call-cost 

isdisplayed in the LCD of iPECS IP or LDP Phone. 

OFF 

ON 

OFF 

Active PTT 

GroupNumber 

A station can be assigned to a PTT (Push-to-Talk) group and 

thegroup enabled so the station can place and receivePTT 

announcements for the group. 

0~9 

 

Hot Desk 

Station 

A station (only IP Phone) can be assigned as a Hot Desk phone. 

Users and agents can login and use resources of the system 

through the Hot Desk phone. 

OFF 

ON 

OFF 

SMDR Hidden 

DialedDigits 

If this feature enables, the dialed digit can be hided on SMDR 

output. 

Disable 

Enable 

Disable 

Summary of Contents for iPECS eMG100















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands