manualshive.com logo in svg

LG-Ericsson iPECS eMG100, Programming Manual

Share
Download
LG-Ericsson iPECS eMG100 Programming Manual Download Page 54

iPECS eMG80/100& eMG800 & UCP & vUCP 
Administration and Programming Manual 

Issue 2.3 

37 

Table 3.3.3.2-1 STATION ATTRIBUTES I (PGM 111) 

BTN 

ATTRIBUTE/DISPLAY 

DESCRIPTION 

RANGE 

DEFAULT 

9 

100-110 SPKR/HEAD 

(1:SPKR/0:HEAD): SPKR 

Selects Speakerphone mode or Headset 

mode 

0: Headset 

1: Speaker 

SPKR 

10 

100-110 LCD DISP LED 

(1:RING/0:MWI): MWI 

The LCD LED, upper left of LCD, may be 

used for Intercom Call ring Indication or 

Message Wait Indication. 

0: MWI 

1: Ring 

MWI 

11 

100-110 LOOP LCR ACCT 

(1:ON/0:OFF) : OFF 

Station based LOOP LCR authorization; this 

is used for LOOP LCR operation. 

0: OFF 

1: ON 

OFF 

12 

100-110 CALL COVERAGE 

(1:ON/0:OFF) : OFF 

The Call Coverage feature permits an iPECS 

Phone user to receive ring and answer calls 

to other stations. 

0: OFF 

1: ON 

OFF 

13 

100-110 CALL COVERAGE 

DELAY RING: 0 

When a covered station rings, the 

{CALL 

COVERAGE} 

button LED will flash at the 

covering station and will receive ring 

(immediate or delayed, 0 to 9 ring cycles). 

0~9 

0 

14 

100-110 OFFNET FWD 

(1:DIS/0:EN):ENABLE 

A station must be allowed Off Net Fwd to 

forward external incoming calls outside the 

system or otherwise establish a CO-to-CO 

connection (Unsupervised Conference). 

(Except USA version) 

0: Enable 

1: Disable 

Enable 

15 

100-110 FORCED ICM 

(1:ON/0:OFF) : OFF 

When placing an intercom call, a user can 

change the ICM signaling mode, Tone Ring 

to Hands free answer mode or HF Answer to 

Tone Ring. 

0: OFF 

1: ON 

OFF 

16 

100-110 ACT PTT GRP 

ACTIVE PTT GROUP: 

A station can be assigned to a PTT group 

and the group enabled so the station can 

place and receive PTT announcements for 

the group. 

0~9 

. 

17 

100-110 ICM GROUP 

(01-15): 01 

Assigns station to an ICM Tenancy Group, 

refer to PGM 125. 

eMG80/100:1~15, eMG800:0~32 

Refer to 

description 

1 

18 

100-100 VMIU/VMIB 

BOARD 

USE 1ST VMIU/VMIB 

Assigns the VMIU or VMIB where messages 

for the station are stored. 

Sequencen

umber. 

 

19 

100-110 SIP UID TBL 

(000-140) : 000 

Index to SIP User ID table, PGM 126, for the 

station. Note PGM 126 is accessible by Web 

only. 

000-140 

000 

20 

100-110 CAMP ON TONE 

(1:ON/0:OFF) : ON 

Permits camp on tone to be sent to a station 

when the station receives camp-on request. 

0: OFF 

1: ON 

ON 

Summary of Contents for iPECS eMG100















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands